Lure epoxy, envirotex lite, mini, 60 mlProductnummer: le 60 € 9,95
Mengverhouding 1:1 ml
Hardt transparant uit
Verwerkingstijd ca. 15 minuten
De enige echte envirotex, sterk, strak, glanzend, enz.
Goed voor ongeveer 9 aasjes.
De enige echte
Epoxy bestaat uit 2 componenten; hars en harder.
Deze hebben een eenvoudige mengverhouding van 1:1 (1 deel hars op 1 deel harder). De epoxy heeft en neutrale geur en hardt transparant uit.
Deze epoxy geeft uw kunstaas een glad oppervlak.
Deze hars is dunvloeibaar en dringt diep door in een zuigende ondergrond.
Lure epoxy zeer goed mengen. 5 minuten laten rusten, en dan aanbrengen.
Vergeet niet de 5 ml spuiten bij te bestellen.
Epoxy moet op een veilige manier worden opgeslagen zodat het niet, in het bijzonder voor kinderen, in contact met de blote huid komt of ingeslikt kan worden.
Er is een klein percentage mensen dat een allergie heeft voor epoxy. Dit kan zich uiten in roodheid, jeuk, tranende ogen en/of kortademigheid. Deze symptomen gaan over maar vermijd voortaan direct (huid)contact met niet uitgeharde epoxy.
Gebruik altijd gezichts- en huidbescherming tijdens het werken met epoxy. Gebruik tijdens het schuren van hout of epoxy altijd deugdelijke adembescherming! Mocht de huid toch in contact komen met epoxy, gebruik dan liever geen chemische middelen.
Azijn helpt het best om de nog niet uitgeharde epoxy te verwijderen.
In het algemeen: gebruik altijd handschoenen en vermijd contact tussen nog niet uitgeharde epoxyhars en -harder en de blote huid.
De hars en de harder hebben een lage brandbaarheid, maar onthoudt dat andere chemische middelen die worden gebruikt, zoals aceton en thinner, wel zeer licht ontvlambaar zijn. Niet inademen. Mochten er zich toch gezondheidsproblemen voordoen consulteer dan een arts.
in this article I will elaborate on the best way to use of Envirotex Lite and what to do in case you encounter some problems along the way. Envirotex Lite is a two component epoxy lacquer that will harden to a high gloss, rock hard and scratch resistant finish. When you open the package you will notice that two plastic cans and a manual are included. The two cans contain ‘resin’ and ‘hardener’. Before you start, read the manal carefully. It contains a lot of useful information. You can also find this manual on www.lurebuilding.nl under ‘techniques’, then click on the topic ‘finishing’. You can obtain a measuring cup with most packages. This cup measures both in milliliter and ounces. I will now explain how to use Envirotex Lite.
- 1 package of Envirotex Lite
- 1 cheap brush with a width of 2,5cm to 3cm
- A measuring cup or something similar with flat sides and a flat bottom
- A cheap plastic cup
- A flat stick to mix the two components
How to use this product:
1) For a jerkbait with an average size of 15cm, you will need approximately 5ml of lacquer. This means 5ml of mixed components. For smaller lures you will obviously need less lacquer, for larger baits you’ll need more lacquer. You need to find out how much lacquer you will have to make by using the good old method of trial and error. It is better to make too much lacquer than too little. Mixing more lacquer while you are coating baits equals asking for trouble! When I talk about lacquer, I mean mixing the two components in a 1/1 scale. When you mix 5ml of lacquer, you will need 2,5ml of resin and 2,5ml of hardener. You need to measure two equal shares of each component. If you want to make 100ml of lacquer, you will need exactly 50ml of resin and exactly 50ml of hardener. It is difficult to mix a small amount of lacquer so make sure you need to coat several baits in one go.
2) Take the measuring cup or a similar cup with flat sides and a flat bottom. Only this type of cup is suitable for mixing Envirotex Lite because it is of the utmost importance to mix the two components properly. Let us continue with the exemplary amount of 100ml of lacquer. Measure exactly 50ml of resin in the measuring cup. The next thing to do is to add exactly 50ml of hardener in the same cup. Take the mixing stick. In the original manual you are advised to use a wooden stick that you find in certain ice creams. I use a plastic mixing stick from a kit for mixing epoxy glue. The mixing stick has to be flat and thin, that’s the main thing.
3) After you joined both components, you have about 25 minutes before the lacquer hardened too much to be able to brush it on the lure. Therefore it is important that you know what to do next by heart so you won’t loose any time. Take the mixing stick and start to mix the lacquer thoroughly by stirring and scooping through the lacquer. Don’t forget to scrape the sides and the bottom properly. Stir thoroughly and at a good speed. It’s very important that all the lacquer is mixed properly. If some part of the mixture hasn’t been mixed properly, you might end up brushing pure resin or hardener on your lures. This simply won’t harden so the lure will be ruined. I stir and scrape during 3 minutes at a good pace. You will notice that the lacquer is no longer clear and that an abundance of air bubbles starts to appear in the lacquer. This is normal. This means that the two components are reacting with eachother.
4) Take the cheap plastic cup and pour the lacquer from the measuring cup into the plastic cup. Put the measuring cup upside down on a news paper or a piece of cardboard. Leave it like this until the lacquer has hardened fully. When the lacquer has hardened, you can easily remove whatever is left of the lacquer in the measuring cup so you’ll be able to use it again. Take the mixing stick and stir the mixture in the plastic cup for another two minutes. Clean the mixing stick with a piece of cloth so you can use it again afterwards. The mixture is ready to be brushed on the lures. The next thing you’ll need to do is take the brush. Why do I use a cheap brush? Well, it is near impossible to clean the brush after having used it to brush epoxy lacquer on baits. The lacquer becomes really hard so the brush becomes useless after having used it once.
5) You need to fit the lures with stick-on eyes and screw-eyes before you start to lacquer the baits. I make S-shaped hangers from steel wire (used for jerkbait leaders) to hang the lures away and to be able to handle them while lacquering the baits. Apply a thick coat of lacquer on the lures and make sure every spot on the lure has been covered with lacquer. Now hang the jerkbait away to allow the excess lacquer to drop from the lure. You will notice the air bubbles will start to appear after you hung the lures away on a rack. Again, this is normal. Just continue on the next few lures. I usually lacquer a batch of 20 baits in one go. A short calculation will make things a lot clearer: 20x 5ml per jerkbait equals 100ml. I divide these 20 jerkbaits in four batches of five lures. This needs to be explained. I brush lacquer on five baits first and then I hang them away on a rack to allow the excess lacquer to flow from the lure. Then I start on the second batch of five baits. I hang them on the rack, just like I did for the first five lures. I take the first five baits again and exhale on them to make the air bubbles burst. Only by exhaling on the baits will the bubbles burst. The CO2 in your breath will make the air bubbles burst. Don’t blow hard on the baits, simply exhale. The lacquer will fill any holes that might appear when an air bubble bursts. This is one of the good qualities of Envirotex Lite. Next I start on the third batch of five baits and I exhale on the second batch of five baits.
6) I continue doing this until all the baits have been handled and hung away on the rack to allow the lacquer to harden properly. Make sure all of this happens in 20 minutes time. Once you know what to do, you’ll make it in less than 20 minutes. Lacquer might flow from the lure during the next few hours so make sure you put some old news papers underneath the drying rack. Make sure you mix enough lacquer. I can’t stress this enough: DO NOT try to get the last bit of lacquer out of the plastic cup to coat one extra lure. Often the lacquer on the sqides and on the bottom is mixed less well than in the middle. To make sure you won’t get into trouble, never scrape the last bit of lacquer out of the cup. Try to avoid contact between the brush and the sides and bottom as much as possible.
7) Now it’s time to hang the lures away in a dry, well ventilated and dust free room where the room temperature is about 20°C. Envirotex Lite doesn’t smell at all so you can hang the lures to dry in a room. Often a garage is too damp and too cold. 20°C is about the ideal temperature to allow the envirotex to harden. Warmer is ok, colder is to be avoided. The colder it is, the longer it takes for the lacquer to harden and the larger the risk will be that the lacquer doesn’t harden 100%. A dry room is necessary because moisture in the air hampers the hardening process. A dust free room is important for the end result. Dust particles that end up on the lacquer while the lacquer is hardening can’t be removed. It has little to do with the hardening process but more with the looks of the bait when the lacquer has cured properly. It would a crying shame that your lure would be ruined right at the end of the building process.
8) How long do you need to wait for the lacquer to harden. The official manual mentions 72 hours, or three full days. After having used envirotex lite for the past three years, I can say this is a bit exaggerated. Under normal circumstances (mixing the lacquer properly, a well ventilated room, a dry and dust free room, 20°C room temperature) it takes about 48 hours or two full days. The lacquer is dust free (no particles will attach themselves on the lacquer after that period) after about 24 hours. This doesn’t mean that you can start to fondle with your newly acquired baits unless you wish to fit them with an original signature: your own fingerprints! These fingerprints can’t be removed so be patient. As you can see, coating baits with envirotex lite isn’t something you do the day before you leave on a fishing trip. Take your time to plan and execute every step.
9) After two days you can touch the jerkbaits. If the touch feels dry and hard, you can open the screw-eyes by using a drill bit or a pair of scissors. I use a drill bit and the point of a pair or scissors. To remove some smaller bits I use a sharp knife. Be careful when you try to open the screw-eyes. I have had it happen repeatedly in the past three years that either the knife or the point of the pair of scissors ended up in my hand when I wasn’t paying attention.
So, now you know how to use envirotex lite. I will now list some frequently encountered problems and what to do to solve them. Sometimes there is no other option than to sand down the blank again and to start all over but in some cases it can be avoided.
1) “The lacquer hasn’t hardened after 48 hours or hasn’t hardened all oer the jerkbait”. The most obvious reasons are:
- You didn’t mix the components long or thoroughly enough or you forgot to scrape the sides and the bottom of the measuring cup.
- You didn’t mix the components in a 1/1 scale
- You scraped the last bit of lacquer out of the plastic cup
- The room temperature was too low
- The room where you hung the baits to dry was damp and insufficiently ventilated
There is very little that you can do to solve this problem. The way I see it, there are two options. Number one is to remove everything from the lure and start all over again. The second option is to use a piece of waterproof sanding paper to roughen the surface and to add a second coat of lacquer. Make sure that everything has been mixed properly this time.
2) “Air bubbles remain after the lacquer has hardened”.
- I can advise you to check the lures up to about an hour after the last bait has been lacquered. When you discover new air bubbles, exhale on the lure until they disappear. The longer you wait to do this, the less likely it is that you will manage to remove the air bubbles. It’s not the heat from your breath that makes the air bubbles burst but the CO2 in your breath. Don’t try to remove them with a lighter or matches. The flame might blacken the lacquer. Then you will be forced to start all over again …
3) “I want to add glitters to the lacquer”.
- If you want to add glitters to the lacquer to make the finished lure a little more attractive, you should use micro glitters. You can buy small plastic cans with these glitters in most hobby stores. These glitters are so small that they can hardly be felt after the lacquer has hardened. You can even create special effects by adding several different colors of glitters to the lacquer. Don’t use too much glitters bebcause this upsets the consistency of the lacquer. Add the glitters after you have mixed the two components of the envirotex lite.
4) “How about adding multiple coats of envirotex lite?”
- In general it suffices to add only a single coat. Should you have missed a spot, the first coat didn’t harden properly or you simply want to add a second coat, you can add a second coat.
- Wait 24 hours before you touch the jerkbaits to add a second coat. Lightly sand the coating with waterproof sanding paper to roughen the surface so the second coat will stick better to the first one. Clean the surface with a moist piece of cloth. You will know when to stop sanding when the surface becomes dull and the gloss disappears. Don’t use a piece of cloth with distinct fibers in it. Again, hang the bait to dry and once it has dried, repeat the process as mentioned above.
- A second coat can be necessary for the reasons mentioned above but don’t exaggerate. It really isn’t necessary to add more than two coats.
5)"The Resin has Crystals in it. How can I get these to disappear?"
- This may happen when the Resin is stocked for a longer Period. If you place the bottle in hot water, the Crystals will disappear, and you can use the envirotex again.
iets voor jou?
- Maatbekertje 30 ml € 0,39 Bestel
- 5 ml injectie spuit € 0,69 Bestel